News
How to make Cover Button Paper Clips/Bookmarks with I Like Big Buttons! DIY Kit March 21 2022
Here is what you will receive a DIY Cover Button Jumbo Paper Clip KIT from ILikeBigButtons.com. Just a few quick steps to make a gift for the booklover in your life!
How to make Cover Button Bookmarks here.
How to make Cover Button Barrettes with I Like Big Buttons! DIY Kit March 15 2022
How to make Cover Button Barrettes with I Like Big Buttons! DIY Kit
Here is what you will receive a DIY Cover Button Barrette KIT from ILikeBigButtons.com. Just a few quick steps to make a fun accent for any outfit or gift for a loved one!
How to make Cover Button Badge Reels with I Like Big Buttons! DIY Kit March 10 2022
Here is what you will receive a DIY Cover Button Badge Reel KIT from ILikeBigButtons.com. Just a few quick steps to make a fun accent for any nurse, teacher, or work ID or gift for a loved one!
Pack An Order With Us @ ILikeBigButtons.com January 31 2022
I thought you might enjoy a glimpse inside the order preparation and shipping process at ILikeBigButtons.com -- This order was a fun one! 50+ crafty items in a variety of finishes and sizes. Cover Button DIY Kits, Badge Reels, Flat Back Cover Buttons, Template & Tools, Key Fob Hardware, Barrettes & Bobby Pins, & Wire Back Cover Buttons! Oh My! You all like to keep me on my toes!
Shop with confidence!
Where to find us:
- Join our Facebook group!
- Like us on Facebook.
- Visit us on our YouTube Channel.
- Follow us on Pinterest.
- Follow us on Instagram.
- Follow us on Twitter.
Thank you for your interest! Have a great crafty week!
I Like Big Buttons and crew!
How To Make A KAM Plastic Snap Cord Keepers @ ILikeBigButtons.com January 07 2022
With cords abounding in my life and house especially after Christmas, 🤪 we needed a better way to manage them all. Here are the results of my efforts. Cord keepers/organizers to simplify my life and corral the cords we can't live without.
See Full Pictorial here.
Wednesday Humor @ ILikeBigButtons.com January 05 2022
Christmas Gift Idea #2: Key Fob Wristlets @ ILikeBigButtons.com December 02 2021
- 11"x2.25" fabric strip (of your choosing)
- 1" or 1.25" cotton webbing (depending on Key Fob Hardware Size)
- Heat N Bond or Fusible Tape
- 1" or 1.25" Key Fob Hardware set
- Key Fob Hardware Pliers
- Sewing Clips
- Fray Stop
- Sewing Machine
- Iron
2. I made a template out of chipboard that was 12"x1.25" to help me achieve a consistent size and look. Fold in and iron the fabric to 1.25" wide.
4. Remove Heat N Bond backing and turn finished Fabric Strip right side up and iron to Cotton Webbing making sure to center it.
5. Stitch along the edge of your Fabric strip, securing the edge onto the webbing. Work slowly, keeping close to the edge. Go the whole length on both sides.
6. Fold the Cotton Webbing in half, right sides facing out and match up the ends. Secure with Sewing Clips and stitch the ends together with a zigzag stitch. Trim any loose threads and lightly coat the end in Fray Stop or equivalent liquid to help resist fraying over time.
8. Using your Key Fob Hardware pliers squeeze the Key Fob Hardware closed a little at a time. I like to go back and forth a couple times so that I don't over-crimp one side too much.
9. Add the Key Ring and Yay!!! You are done. Good Job!!!
* Instructions for 1.25" Key Fob Hardware (adjust accordingly if using 1" Hardware)
To see all our Key Fob Hardware Tutorials, visit our Projects section here.
Keeping In Touch With Us @ ILikeBigButtons.com November 17 2021
Make sure you are a member of our Facebook Group !!!
At least once a week, we have a specific item or general sale going on. They will be posted in our --> I Like Big Buttons! Facebook Group <-- when they go live. You can always check our Pinned post in our Group where we list the sales currently going on. Don't forget to turn ON your notifications so you don't miss our latest news and deals.
Missing posts or sales?
Make sure you stay active in the group! Facebook is so huge that often even having your notifications 'on' doesn't always work.
Ways to stay active in I Like Big Buttons Facebook Group:
1) Simply Like or react to the posts in our group
2) Post your relevant I Like Big Buttons! craft projects for us all to enjoy
3) Comment and show support to other members posts in our group
Show Facebook's algorithm you want to see more from I Like Big Buttons! group. The more active you are, the more you will see.
You can also sign up for our I Like Big Buttons! Newsletter to be notified by email of our current sales and latest news.
Sign up TODAY!
Have a great crafty week! I Like Big Buttons and crew!
Crafty Wednesday - Fall-Themed Key Fob Wristlet @ ILikeBigButtons.com November 04 2021
😍 Friend Request! I had a friend request some Fall-themed Key Fob Wristlets. I love how they turned out! 😍
ILikeBigButtons.com Supply List:
- Key Fob Hardware
- Pendant Bezels (Size 36 and Size 60)
- Cover Buttons (Size 36 and Size 60)
- Lobster Clasps
For more Crafty Inspiration, visit our Key Fob Hardware Inspiration Boards.
Top DIY Craft Project Picks @ ILikeBigButtons.com October 08 2021
😍 These Marvel Key Fob Wristlets are a favorite in the I Like Big Buttons! household. 😍
ILikeBigButtons.com Supply List:
KAM Plastic Snap Love Video @ ILikeBigButtons.com September 13 2021
I am busy updating the ILikeBigButtons.com product images and couldn't help making a short video of the KAM plastic snaps all lined up. All the colors make me so happy!
KAM Plastic Snap Love Video
ILikeBigButtons.com carries a rainbow of KAM plastic snap colors in Size 20 (Most Popular Size for Craft Projects) and Size 16 (Doll/Ribbon Projects) and much more.
Visit our KAM plastic snaps page to see our full selections of KAM plastic snaps and KAM tools.
Check out our KAM Snap Inspiration Board to find a plethora of Tutorials and Ideas for how to use KAM plastic snaps in your crafty projects.
Have a great crafty day,
The Crew @ ILikeBigButtons.com
So many 😍 Key Fob Wristlets @ ILikeBigButtons.com September 01 2021
So many 😍 Key Fob Wristlets.
ILikeBigButtons.com Supply List:
To see other great Key Fob Hardware, Pendant Bezel, and Cover Button ideas, visit our DIY Project section here.
Monday Humor @ ILikeBigButtons.com August 30 2021
Yep! I'll admit it. 😜
Our Pale Pink (B21) KAM Plastic Snap is delicate pink and reminds me of all things girly and precious. If you are not into Pale Pink, we carry 9 other shades of red, 15 shades of pink, and 130+ unique colors of snaps.
🤓 What are you working on today!?! 🤓 August 27 2021
School Must-Haves @ ILikeBigButtons.com August 24 2021
With the school year starting back up, I couldn't resist. 😄
Shop Cover Buttons @ ILikeBigButtons.com
Shop Jumbo Paper Clips @ ILikeBigButtons.com
To see other great Cover Button and Jumbo Paper Clip ideas, visit our DIY Project section here.
Brand New! Hearts & Stars & Flowers! Oh my! @ ILikeBigButtons.com August 10 2021
Brand New! Hearts & Stars & Flowers! Oh my!
Check out I Like Big Buttons! Key Fob Hardware with shaped split rings!!!
Fabric Cover Button Jumbo Paper Clips @ ILikeBigButtons.com July 13 2021
I'm in with Jumbo Paper Clips and Cover Buttons.
Quick & easy craft with stunning results!
Upcycled Messenger Bag/Purse Tutorial @ ILikeBigButtons.com July 08 2021
We are a cat-loving family here at I Like Big Buttons! As such, we have a few fluffy friends scurrying around. A while back, my husband picked up a few bags of cat food that were made of a more durable material than the paper bags ones and had cute kitty images on them. I couldn't resist turning them into some cute messenger bags for a couple of my little cat lovers. 🙂 🐈
How to make an Upcycled/Recycled Messenger Bag/Purse with KAM Snaps and Pet Food Bag
Supplies:
- Pet Food Bag of your choice (Look for the ones made of woven plastic)
- Marine Vinyl or a material of your choice
- 2 KAM Snap Sets (Depending on the thickness of the material you may want Long Prong)
- KAM Snap Pliers and Awl
- 1″ Cotton Webbing
- Scissors/Rotary Blade
- Standard Sewing Machine
1. Cut the bag along the seams. I plan on making 2 bags with it. For this project, I am focusing on making each bag with a kitty image front and center. Use a damp cloth to wipe the leftover cat food crumbs from the interior of the bags and let air dry. This doesn't take more than a few minutes.
2. Decide on your shape. I like to craft off the cuff. This lid of a storage container was just the right size and shape to showcase the kitty image. Trace around it with a marker.
3. I picked the height based on the image. I left a 1" above each kitty image. *If I did it again, I might do 2" or 3" instead. As you will see later, the flap of the bag covers some of the image. If I had dropped it another inch I think it would have looked slightly better when snapped closed.
4. Cut 2 pieces of Marine Vinyl or material of your choice the same size at the kitty images. I had some vinyl left over from a summer chair reupholstering product. I love it because the color goes nicely with the kitty image and it is durable.
5. Cut two flaps for the messenger bags. I cut them the same width as the bags and longer than I thought I would need so I could adjust on the fly.
6. Using a 1/2" seam sew the kitty image to the front piece of Marine Vinyl, right sides together. I chose to put the Marine Vinyl front to the front so that the interior of the bag was uniform, but you could turn the right side of the Marine Vinyl inward so that it was to the inside of the bag. Sewer's choice. :)
7. Fold the sewed seam flat and smooth. Then, fold it until the kitty image is right side out. Smooth the sewed seam and Marine Vinyl.
8. Sew 1/4" seam along the top of the finished edge.
9. Fold the top edge of the back piece of the bag over a 1/2". Sew 1/4" seam along the edge, creating a finished edge.
10. For the top flap, I created a simple square with three finished edges. Marine Vinyl is durable and the raw edges hold up nicely. If using another material, you will have to give consideration to the material you are using and adjust accordingly. The messenger bag/purse will be about 8" wide when finished so I made the flaps slightly smaller at 7.75". *If I did it again, I might have shaved off a little bit more to give the shoulder strap more room to fill.
11. I, then, cut the height of the flap down to 3" because I wanted to see as much of the kitty image as I could after the KAM plastic snap was installed.
12. Align and use a zigzag stitch to attach the flap to the back piece of the purse. Make sure to center it.
13. Put right sides together and sew the 2 sides and bottom of the purse with a 3/8" to 1/2" seam. Make sure to use a Stay Stitch the beginning and end of your sewing so that the stitches stay put.
14. Turn the bags right side out and square the corners as much as possible. I used the backside of a Sharpie marker to help square the corners. Remember I slightly rounded them so they won't be perfectly square. Smooth bags flat.
15. Measure the center of the flap and use a KAM awl to poke a hole for the KAM plastic snap that you will adding. I am only going through 1 layer of Marine Vinyl so a Standard Prong snap will work. If you are using thicker material or multiple layers, I would recommend our Long Prong KAM plastic snaps.
16. Install KAM plastic snap (Cap and Socket).
17. Repeat in front of the bag, where KAM plastic snap lines up. I poked the hole through both layers at once so that I had a point of reference. Then I widened the hole after double-checking the placement of the internal hole. Install KAM plastic snap (Cap and Stud).
18. I think they turned out super cute! Now to add shoulder straps.
19. For the sake of time and my sanity, I simply attached the shoulder straps with a half of a KAM snap set (Cap and Socket). I used the snap like a rivet. I also used Long Prong KAM plastic snaps for this piece because I was working with the thickness of the Marine Vinyl and Cotton Webbing. *I doubled the edge of the Cotton Webbing over on itself and sewed a straight line back and forth across it a half dozen times so it doesn't unravel. With Polyester Webbing, you could melt the edge to secure it.
20. Tada!!! I think they turned out great, it took less than 2 hours to make both of them, and my little cat lovers are ecstatic. They have a new place to store their treasures.
😻 😻 😻
Water Bottle Charm Markers @ ILikeBigButtons.com June 15 2021
Congratulations, Class of 2021!!! We had a graduate this year. We are still trying to wrap our mind around it, given that we just brought her home from the hospital not so long ago, but now we are celebrating her like she is a Rockstar!
We were able to throw her a celebration with our family and closest friends. To make the "Whose Water Bottle is Whose?" game more manageable, we raided our Pacifier Supplies inventory and used O-Ring Pacifier Adapters in all 14 colors to mark the water bottles, so they were unique.
It is as simple as placing an O-Ring over the bottle cap. The O-Rings nestle snuggly just under the rim and can be slipped back off and washed for reuse.
To see this tutorial and other I Like Big Buttons! Crafty Ideas visit our Craft Inspiration Boards here.
Hands-free Water Bottle Holder @ ILikeBigButtons.com June 11 2021
My oldest is headed off on a class trip to Silverwood Theme Park. Rollercoaster rides, caramel apples, sunshine, and lots of laughter. A hands-free Water Bottle, so she can keep moving and not worry about keeping hydrated, is a must.
I made a couple of quick water bottle holders from ILikeBigButtons.com craft supplies.
Here is what you will need:
- MAM Rings
- KAM Plastic Snaps & Pliers
- A Piece of Ribbon
Making Lace & Fabric Cover Button Earrings @ ILikeBigButtons.com June 09 2021
Supplies:
- Flat Back Cover Buttons (I used Size 24, Size 30, and Size 36 Cover Buttons)
- Cover Button Assembly Tools
- Cover Button Templates
- Fabric Scraps
- Lace Scraps
- E6000 Adhesive or Hot Glue
- Sharpie Permanent Marker
- Surgical Stainless Steel Earring Posts and Backs
Instructions:
1. Cut your fabric scrap. You will want a circle that is about twice the diameter of your button blank or use one of our handy Plastic Cover Button Templates.
2. Put your lace piece in the larger assembly tool piece (RIGHT SIDE DOWN). Then, put your fabric piece in the larger assembly tool piece (RIGHT SIDE DOWN). When you look into the tool you want to see the back of the fabric.
3. Place the button front (the domed piece) on top of the fabric. Leave the fabric edges hanging out.
4. Press the Cover Button edges down into the tool.
5. Place the back cover button piece on top of your fabric and button front. If the cover button will be subject to repeated tugging from the back, you may want to add a little e6000 adhesive before attaching the back.
6. Take the smaller piece of the assembly tool and with the open side down place it on the button back.
7. Press down. You may hear a pop when the last bit of the button back slips into place. If you take the tool out and the button is not completely secured, just put it back in and press down again.
8. When you take the small assembly tool piece off, the fabric edges will be secured underneath the button back.
9. Remove the button from the larger assembly tool piece.
10. Tada! First step complete.
11. Lightly scuff the back of the Cover Button so the glue will adhere better (not essential but recommended).
12. Clean both surfaces of dust. I used rubbing alcohol and a cotton swab.
13. Apply E6000 to back of Cover Button or Earring Post.
14. Press Earring Post into place and remove any extra Adhesive. On smaller sized Cover Buttons center the post, as they increase in size adjust post towards top.
15. Let dry, add Earring Backing/Nut, and enjoy.
16. Tada! Lace and Fabric Cover Button Earrings are great a gifts or as products for your shop.
How To Make A Needle Minder/Magnetic Pin Cushion @ ILikeBigButtons.com May 19 2021
I have been working on a lot of crafty projects recently and I needed a few new handy sewing accessories: Fabric Cover Button Needle Minder/Pin Cushion. I love the splash of color they add to my sewing station and their usefulness!
Supplies:
- 1 Completed Size 75 (1 7/8 inch / 48 mm) Fabric Cover Button
- Fabric Of Your Choice
- 1x Standard Round Magnet (Approximately 3/4" Round)
- E6000, Hot Glue, or comparable adhesive
I Like Big Buttons! - Picture Tutorial Below:
1. Cut your fabric scrap. You will want a circle that is about twice the diameter of your button blank. *TIP* Our All-In-One Cover Button Template makes creating the right size circle of fabric a breeze.
2. Put your fabric piece in the larger assembly tool piece (RIGHT SIDE DOWN). When you look into the tool you want to see the back of the fabric.
3. Glue the magnet inside the back of the Cover Button with Hot Glue or E6000.
4. Place the button front (the domed piece) on top of the fabric. Leave the fabric edges hanging out.
5. Press the cover button edges down into the tool. *TIP* To make it easier on my fingers, I use a sharpie marker to apply pressure.
6. Place the back cover button piece on top of your fabric and button front. *TIP* If the cover button will be subject to repeated tugging from the back, you may want to add a little e6000 adhesive before attaching the back.
7. Take the smaller piece of the assembly tool and with the open side down place it on the button back.
8. Press down. You may hear a pop when the last bit of the button back slips into place. If you take the tool out and the button is not completely secured, just put it back in and press down again. *TIP* I often use a flat piece of wood to apply pressure, again to save my fingers. It also helps to avoid the button back going in at an angle.
9. When you take the small assembly tool piece off, the fabric edges will be secured underneath the button back.
9. Remove the button from the larger assembly tool piece.
10. Tada! Now you have an attractive Pin Cushion/Needle Holder for your sewing room.
To see other great Fabric Cover Button ideas, visit our DIY Project section here.
Crafty Friday - Key Fob Wristlet and Key Chain @ ILikeBigButtons.com May 14 2021
😍 Made a WSU Key Fob Wristlet and Key Chain for a friend's daughter today using ILikeBigButtons.com supplies. I love how they turned out! 😍
ILikeBigButtons.com Supply List:
- Key Fob Hardware
- Pendant Bezels (Size 36 and Size 60)
- Cover Buttons (Size 36 and Size 60)
- Lobster Clasps
For more Crafty Inspiration, visit our Key Fob Hardware Inspiration Boards.
Making a Key Fob Lip Balm Holder @ ILikeBigButtons.com May 12 2021
Supplies:
- 15.5" x 2.25" of Cotton Fabric
- 15.5" x 2.25" piece of Fusible Interfacing
- 1.25" Key Fob Hardware with Split Rings
- Key Fob Pliers
- Sewing Clips
- Standard Sewing Machine
- Iron and Ironing Board
- Scissors
Instructions:
- Cut a 15.5" x 2.25" piece of Cotton Fabric and Fusible Interfacing. These measurements will work for a standard Lip Balm Tube and a standard Blistex Tube. You may need to adjust measures for your favorite lip product.
- Iron the Fusible Interfacing to the wrong side of your fabric.
- Fold right sides together width-wise and sew both long sides with a 1/4" seam. Do not sew short sides.
- Turn the tube right side out through the open side, iron flat, and sew the open short side closed with a zig-zag stitch.
- Fold zig-zag side back on itself 1 1/4". Sew straight stitch 1/2" from the top, and again at 5/8" from the top. This is what it will look like from the back.
- Here is how the front turned out. This will be the front of the pocket on the Lip Balm Holder.
- Fold the tab that will be the front of the pocket at 2 3/4". Make sure the zig-zag stitch is hidden. Use Sewing Clips to hold the front pocket in place while sewing. Stitch at 1/4" seam around the whole holder. And again at 1/8". Start and finish at the top edge so that your start and finish stitches will be hidden.
- Center the 1.25" Key Fob Hardware on the top edge of the Lip Balm Holder.
- Using Key Fob Hardware Pliers squeeze the Key Fob Hardware closed with gentle pressure. Sometimes, I go back and forth from left to right added a little bit of pressure to each side until it eases together. Our Key Fob Hardware Pliers make this easy to do. Make sure the teeth in the Key Fob Hardware are sunk securely into the fabric.
- Tada! These little Lip Balm Holders were easy to make and are great as a quick thoughtful gift for a loved one who hates chapped lips.
- Hang them on your keychain, the outside of your purse, or anywhere you need for quick access.
Jumbo Paper Clip Size Comparison April 08 2021
From Left to Right - Standard (1.25 Inch), Large (2 Inch), and Jumbo (3.5 Inch)
- Attach size 36 (7/8" - 23 mm), size 45 (1 1/8" - 28 mm), or size 60 (1 1/2" - 38 mm) flat back cover buttons.
- Glue on flat beads, paper punches, charms, gemstones, cabochons, silk flowers, and much more!
- An adhesive such as E-6000 works great for attaching your crafty items.
Courtesy of craftycjaeger Flower Embellished Jumbo Paper Clips
Making Cover Button Paper Clip Bookmarks @ ILikeBigButtons.com April 05 2021
How To Make Fabric Cover Button Jumbo Paper Clip Bookmarks:
Supplies:
- 1 Completed Flat Back Fabric Cover Button (Attach size 36 (7/8" - 23 mm), size 45 (1 1/8" - 28 mm), or size 60 (1 1/2" - 38 mm) flat back cover buttons.)
- 1 Jumbo Paper Clip
- E6000 or comparable adhesive
Instructions:
- Follow these instructions to make Flat Back Fabric Covered Buttons.
- Make sure the surfaces of the Cover Button back and Paper Clip gluepad are clean and free of oil.
- Apply E6000 to the back of the Cover Button.
- Press into place over the glue pad on the Paper clip at the desired height and remove any extra Adhesive. The bigger the Cover Button the higher you will want to center the cover button.
- Let dry and enjoy.
- Tada!
You are done! Use these adorable Paper Clips to hold your place in your favorite book or cookbook. Enjoy!
Making a Fabric Cover Button Metal Pacifier Clip @ ILikeBigButtons.com February 26 2021
Supplies:
- 2 KAM Snap Sets
- KAM Snap Pliers and Awl
- Round Faced Metal Clips or Enamel Pacifier Clips
- 1 Size 36 Flat Back Cover Button
- Size 36 Assembly Tool
- Size 36 Template
- Fabric Scraps
- E6000 Adhesive
- Pre-made Pacifier Clips (see Pacifier Clip and Supply Tutorials)
Instructions:
- Using our Pacifier Clip and Supply Tutorials make either Ribbon or Fabric Pacifier Clips.
- Cut your fabric scrap. You will want a circle that is about twice the diameter of your button blank. I cut out a Piece of Fabric using my Size 36 Template.
- Put your fabric piece in the larger assembly tool piece (RIGHT SIDE DOWN). When you look into the tool you want to see the back of the fabric.
- Place the button front (the domed piece) on top of the fabric. Leave the fabric edges hanging out. Double check the transparent underside to see if your print is how you would like it. Then press the cover button fabric edges down into the tool.
- Add a dab of E6000 Adhesive to the middle of the cover button cap before installing the Flat Back.
- Place the back cover button piece on top of your fabric and button front.
- Take the smaller piece of the assembly tool and with the open side down place it on the button back.
- Press down. You may hear a pop when the last bit of the button back slips into place. If you take the tool out and the button is not completely secured, just put it back in and press down again.
- When you take the small assembly tool piece off, the fabric edges will be secured underneath the button back.
- Remove the button from the larger assembly tool piece. Tada! My Cover Button is ready to be adhered to a Round Faced Metal Clip.
- Here are the Cover Buttons I made in just a few minutes. Seriously easy, fun and so cute!
- Now take the E6000 Adhesive and put a medium size dab of glue on the back of the cover button about 1/2 of what would fill the back area of the back. This glue is great to work with so don't overly worry about getting the amount right. I was able to cleanly wipe of any excess off when I put on too much and I was also able to remove the button and add a little more when I under did it. This glue is very forgiving.
- Now place the Cover Button over the Round Faced Metal Pacifier Clips and straighten and center your button.
- Press firmly and let set to dry and cure 24-72 hours as recommended by the manufacturer (E6000).
- These are my finished products. I love them and think they turned out beautifully. Below are my examples, completed and installed on Pacifier Clips.
-
Tada!!!
Disclaimer: Keep in mind that although I have rough tested these I in no way recommend you leave your baby alone with these as there are small pieces and if not done properly they may come apart and become a choking hazard. I would recommend these clips under adult supervision only. The maker and/or parent assumes full responsibility when using these pacifier clips.
Wednesday Humor @ ILikeBigButtons.com February 24 2021
😁 I really think it should! 🤣
Our Crimson (B54) KAM Plastic Snap is the beautiful deep red and reminds me of cherry pies and cozy winter days. If you are not into Crimson, we carry 9 other shades of red, 15 shades of pink, and 130+ unique colors of snaps.
Making A Fabric Cover Button Full-Size Clothespin @ ILikeBigButtons.com February 23 2021
How to Make Cover Button Bobby Full-Size Clothespins:
Supplies:
- 1 Completed Flat Back Fabric Cover Button (Attach Size 30 (3/4 inch / 19 mm), Size 36 (7/8 inch / 23 mm), or Size 45 (1 1/8 inch / 28 mm) flat back cover buttons.)
- 1x Full-Size Wooden Clothespin
- 1x Medium Plain Button
- E6000, Hot Glue, or comparable adhesive
Instructions:
- Cut your fabric scrap. You will want a circle that is about twice the diameter of your button blank.
- Put your fabric piece in the larger assembly tool piece (RIGHT SIDE DOWN). When you look into the tool you want to see the back of the fabric.
- Place the button front (the domed piece) on top of the fabric. Leave the fabric edges hanging out.
- Press the cover button edges down into the tool. *TIP* To make it easier on my fingers, I use a sharpie marker to apply pressure.
- Place the back cover button piece on top of your fabric and button front. *TIP* If the cover button will be subject to repeated tugging from the back, you may want to add a little e6000 adhesive before attaching the back.
- Take the smaller piece of the assembly tool and with the open side down place it on the button back.
- Press down. You may hear a pop when the last bit of the button back slips into place. If you take the tool out and the button is not completely secured, just put it back in and press down again. *TIP* I often use a flat piece of wood to apply pressure, again to save my fingers. It also helps to avoid the button back going in at an angle.
- When you take the small assembly tool piece off, the fabric edges will be secured underneath the button back.
- Remove the button from the larger assembly tool piece.
- Tada! Now to attach it to the Clothespin.
- Use Hot Glue or E6000 to adhere a small plain button to the underside of the Cover Button. This is to fill the space between the back and the edges. You can also use felt or some other small object. You just need it to be sturdy enough to offer support. A small plastic button works great for this. You will see that the button is now flush across the bottom. I cut off the little nubs of glue that leaked through the button holes.
- Now adhere the finished Cover Button to the Clothespin. Press into place and center it until you are pleased with the alignment. Set aside to dry.
- Tada! Additional uses:
- Add a thin magnet to the back and use on your magnetic board.
- Add a push pin to the back and use on your cork board.
How To Make A Fabric Cover Button Mini Clothespin
To see other great Fabric Cover Button ideas, visit our DIY Project section here.
Making Fabric Cover Button Bobby Pins @ ILikeBigButtons.com February 19 2021
How to Make Cover Button Bobby Pins:
Supplies:
- 1 Completed Flat Back Fabric Cover Button (Choose your size, Size 20 through Size 45 all work great, size depends on the statement you want to make)
- 1 Bobby Pin
- E6000 or comparable adhesive
Steps:
- Follow these instructions to make Flat Back Fabric Covered Buttons.
- Apply E6000 to back of Cover Button.
- Press Bobby Pin into place and remove any extra Adhesive. On smaller sized Cover buttons center the glue pad, as they increase in size adjust accordingly.
- Let dry and enjoy.
- Tada!
You are done! Wear these adorable Bobby Pins to match or accent your favorite outfit or dress up your favorite t-shirt and jeans for an afternoon outing. Enjoy!
Ribbon and Cotton Webbing Key Fob Tutorial October 05 2020
How to make a Ribbon Key Fob Wristlet:
You will need:
- Scissors
- Sewing Machine
- Iron
Supplies:
- 1.25" Cotton Webbing
- Ribbon (Narrower than the Cotton Webbing)
- Coordinating color thread
- Heat N Bond or Fusible Tape
- 1.25" (32 mm) Key Fob Hardware
- Key Fob Hardware Pliers
Instructions (adjust accordingly for 1" hardware):
- Cut a 10" section of the Cotton Webbing and Ribbon of your choosing.
- Cut a 10" section of Heat N Bond, keeping it thinner than your ribbon.
- Iron the Heat N Bond to your Cotton Webbing, making sure to center it. This is not a necessary step but it makes it easier to sew the Ribbon on especially with embroidered ribbon.
- Iron the Ribbon to the Cotton Webbing.
- Sew up one side of the Ribbon and down the other. The Ribbon should now be securely attached to the Cotton Webbing.
- Trim the edges so they are even.
- Fold the Cotton Webbing in half, right sides facing out and match up the ends.
- Stitch the ends together with a 1/4" seam allowance.
- Trim any loose threads.
- Tuck the sewn seam ends into the Key Fob Hardware, making sure that the Cotton Webbing is centered.
- Using your Key Fob Hardware Pliers with silicone tips to protect the metal from getting scratched, squeeze the Key Fob Hardware closed a little at a time. I like to go back and forth a couple times so that I don't over crimp one side.
- Add the Key Ring and Yay!!! You are done. Good Job!!!
🌺 Cabochon Push Pin Kits and Cover Button Push Pin Kits 🌺 @ ILikeBigButtons.com September 01 2020
DIY Cherry Blossom Cabochons Push Pins/Thumb Tacks KIT (22 mm) - Makes 10
DIY Size 30 (3/4" (19 mm) Covered Button Push Pins/Thumb Tacks KIT - Makes 10
If you are looking for a super easy, fun, and impactful craft project, these decorative push pins are for you and just in time for the beginning of school.
Using our Cabochon DIY Push Pin Kit or Cover Button DIY Push Pin Kit, you can make these message or corkboard accessories that are super cute and well-received without much effort.
Place a small dab of E-6000 or a comparable adhesive on the metal circle glue pad on the push pins. Then simply press the flower cabochon or completed cover button into place and center it. Allow to dry for the recommended amount of time per adhesive's directions and enjoy!
The hardest part is waiting for the glue to dry. 😜
To see other great DIY STARTER KIT options, visit our DIY KITS section here.
Free Downloadable/Printable Chart to attach "G" Custom Colors June 04 2020
Printable Chart/Grid for the "G" Custom Colors | Printable Chart/Grid for the "G" Custom Colors (Flipped/Foldable) |
I Like Big Buttons! Printable Chart/Grid for the "G" Custom Colors (G61 through G130)
My sweet husband created 2 pdf charts for our ILBB "G" KAM Plastic Snaps Custom Colors with a small circle in each square so that your snap caps can be placed neatly in the chart.
He also split it into two charts to make it easier to attach the snaps with pliers or press if you would like. They can also be attached with glue. And he formatted it so that you can choose between either a "both sides up" version or a "flippable" version so you can fold it in half and flip it and have the second half of the chart right side up.
Now, you can have an easy quick reference chart like Standard KAM plastic snap chart for B1 through B60. You can print the charts on paper or cardstock and attach our exclusive "G" Custom Colors for a handy reference guide when ordering or deciding on fabric/snap combinations.
They are available in the above links, but you can also find it on our website in the main menu under "Color Charts".
Where to buy Standard KAM plastic snap chart and samples of our 70 custom colors.
I Like Big Buttons! 📎📎📎 Jumbo Paper Clips 📎📎📎 June 01 2020
Jumbo Paper Clips & Jumbo Paper Clip DIY Kits are 10% OFF
No Coupon Necessary
Time to Stock Up!
Cabochon Bobby Pin Kits by ILikeBigButtons.com May 29 2020
If you are looking for a super easy, fun, and impactful craft project, these are for you. My little girls were thrilled to be the recipients of my craftiness.
Using our Cabochon Bobby Pin DIY Kits, you too can make gifts that are super cute and well-received without much effort.
Supplies:
- Mum or Cherry Blossom Cabochons
- Enameled Bobby Pins
- E6000 Glue or Comparable Adhesive (*glue not included)
We carry a colorful mix of Mums in Small or Medium.
10 mm Mum Cabochons:
16 mm Mum Cabochons:
OR a colorful mix of Cherry Blossom Cabochons in Medium or Large.
16 mm Cherry Blossom Cabochons:
22 mm Cherry Blossom Cabochons:
You pick finish of your bobby pins from a colorful selection:
Place a small dab of E-6000 or a comparable adhesive on the metal circle glue pad on the bobby pin. Then simply press the flower cabochon into place and center it. Allow to dry for the recommended amount of time per adhesive's directions and enjoy!
The hardest part is waiting for the glue to dry. 😜
Tada!
To see other great DIY STARTER KIT options, visit our DIY KITS section here.
Face Mask with Scrunchy Earpieces Using KAM Plastic Snaps Tutorial by ILikeBigButton.com April 23 2020
As a precaution, I have been making our family some face masks. Nothing fancy, I was limited to what supplies I had on hand. I made a mask with Elastic earlier, this one will be with ribbon ties.
So with some fabric scraps, ribbon (they mentioned you could use shoelaces as an option), sewing clips, and my trusting sewing machine, I found a set of instructions and struck out.
Here is the #1 version and #2 version I made:
Supplies:
- Face Mask Instructions (I used these as general guidelines)
- 2x 9.5" x 6.5" pieces of Fabric
- 2x 2" x 12" pieces of Fabric
- 2x 7" of Elastic (this is a good average size, but may need to be adjusted if you are a smaller person)
- KAM Plastic Snaps
- KAM Plastic Snap Pliers
- Sewing Clips
- Sewing Machine
1. Cut out 2x 9.5" x 6.5" fabric rectangles and 2x 2" x 12" fabric rectangles.
2. Iron the 2"x12" in half making a 1"x 12" fabric strip with right side facing in. Make 2.
3. Sew 1/4" seam along the long side (12" long seam) and turn then the tube right side out. Iron smooth.
4. Fish a 7" piece of elastic through the tube, I used a sewing clip to keep the back end of the elastic from getting lost in the tube. Pin the elastic level with the end of the tube. It should start to scrunch up some. The tube is 12" long and the elastic is 7" long. Tuck the fabric into the tube without losing the elastic (use a second pin to keep in place) and sew the finished end of the earpiece that will be exposed. Make 2.
5. With the right side of 9.5" x 6.5" fabric facing up, pin the 2 fabric and elastic earpieces to the bottom corners. Like so.
6. Pin the second piece of 9.5" x 6.5" fabric facing down to the fabric with the earpieces tucked safely inside. Make sure the earpieces don't get caught in the edges while sewing.
7. Sew a 1/4" seam starting about 1/2 way on the long side. Go all the way around the perimeter, stopping when you have about 1.5" to 2" left. Make sure to go back and forth at each of the corners to anchor the ribbon. Leave that gap so that you can turn the face mask right side out.
8. Turn the mask right side out and iron it flat.
9. Make three pleats lengthwise, like you are folding a paper fan. I eyed it and used the sewing clip width as my pleat measurer, but if I was making more than a handful of these, I would make myself a template to make this part easier. The pleats help the mask form around the wearer’s face. Secure each pre-sewn pleat with a sewing clip as pictured above.
10. Now sew a 1/4" stitch around the outer perimeter of the mask face, going back and forward over the corners to add more stability to the ribbon.
11. Then, top stitch a second time around the outer edge about 1/4" in from the first round of stitching.
12. Using your KAM Plastic Snap Pliers and KAM Plastic Snaps add a snap to the upper edge of the mask and the end of the loose earpiece.
13. Tada! You have a finished face mask. This was my husband's favorite because the elastic didn't rub and pull at his ears. I added a second KAM Plastic Snap in pink to each side to make the mask work better with my face.
*Afterthoughts, this mask was the perfect size for my husband, but I added another KAM Plastic Snap an inch in for me on the scrunchy earpiece. This also worked for my teens, but I will need to adjust for my smaller kiddos. This mask seems best sized for teens to adults.
- Page 1 of 2
- Next