Hands-free Water Bottle Holder @ ILikeBigButtons.com June 11 2021

My oldest is headed off on a class trip to Silverwood Theme Park. Rollercoaster rides, caramel apples, sunshine, and lots of laughter. A hands-free Water Bottle, so she can keep moving and not worry about keeping hydrated, is a must.

I made a couple of quick water bottle holders from ILikeBigButtons.com craft supplies.

Here is what you will need:

• MAM Rings
• KAM Plastic Snaps & Pliers
• A Piece of Ribbon

Making a Fabric Cover Button Metal Pacifier Clip @ ILikeBigButtons.com February 26 2021

Supplies:

• 2 KAM Snap Sets
• KAM Snap Pliers and Awl
• Round Faced Metal Clips or Enamel Pacifier Clips
• 1 Size 36 Flat Back Cover Button
• Size 36 Assembly Tool
• Size 36 Template
• Fabric Scraps
• E6000 Adhesive
• Pre-made Pacifier Clips (see Pacifier Clip and Supply Tutorials)

Instructions:

1. Using our Pacifier Clip and Supply Tutorials make either Ribbon or Fabric Pacifier Clips.
2. Cut your fabric scrap. You will want a circle that is about twice the diameter of your button blank.  I cut out a Piece of Fabric using my Size 36 Template.
3. Put your fabric piece in the larger assembly tool piece (RIGHT SIDE DOWN). When you look into the tool you want to see the back of the fabric.
4. Place the button front (the domed piece) on top of the fabric. Leave the fabric edges hanging out.  Double check the transparent underside to see if your print is how you would like it.   Then press the cover button fabric edges down into the tool.
5. Add a dab of E6000 Adhesive to the middle of the cover button cap before installing the Flat Back.
6. Place the back cover button piece on top of your fabric and button front.
7. Take the smaller piece of the assembly tool and with the open side down place it on the button back.
8. Press down. You may hear a pop when the last bit of the button back slips into place. If you take the tool out and the button is not completely secured, just put it back in and press down again.
9. When you take the small assembly tool piece off, the fabric edges will be secured underneath the button back.
10. Remove the button from the larger assembly tool piece.  Tada!  My Cover Button is ready to be adhered to a Round Faced Metal Clip.
11. Here are the Cover Buttons I made in just a few minutes.  Seriously easy, fun and so cute!
12. Now take the E6000 Adhesive and put a medium size dab of glue on the back of the cover button about 1/2 of what would fill the back area of the back.  This glue is great to work with so don't overly worry about getting the amount right.  I was able to cleanly wipe of any excess off when I put on too much and I was also able to remove the button and add a little more when I under did it.  This glue is very forgiving.
13. Now place the Cover Button over the Round Faced Metal Pacifier Clips and straighten and center your button.
14. Press firmly and let set to dry and cure 24-72 hours as recommended by the manufacturer (E6000).
15. These are my finished products.  I love them and think they turned out beautifully.  Below are my examples, completed and installed on Pacifier Clips.

16. Tada!!!

Disclaimer:  Keep in mind that although I have rough tested these I in no way recommend you leave your baby alone with these as there are small pieces and if not done properly they may come apart and become a choking hazard.  I would recommend these clips under adult supervision only.  The maker and/or parent assumes full responsibility when using these pacifier clips.

I Like Big Buttons! - How to make a Fabric Pacifier Clip with KAM Snaps, MAM Ring or O-Ring and an KAM Plastic Pacifier Clip for Button Style Pacifiers June 13 2017

Today, I am making a pretty Fabric Pacifier Clip for Button Style Pacifiers using our silicone MAM rings and O-Rings. Pretty & functional! :)

Supplies for a Fabric Pacifier Clip with Button Style Pacifier Adapters:

• Pacifier with Button Style Grip
• 14" x 3 1/2" Piece of Fabric
• 1 Pacifier Clip per Clip
• 2 KAM Snap Sets per Clip
• KAM Snap Pliers and Awl
• MAM Ring and O-Ring Button Style Adapters
• Standard Sewing Machine and Iron

Instructions:

1.  Choose a piece of Fabric, cut it to the dimensions: 14" x 3 1/2", the finished product once ironed, folded and sewn will be approximately 7/8" wide x 12" long.

2.  Fold both 3 1/2" wide ends in 1/4" and iron flat.

3.  Now fold and iron the fabric in half the long way (14" length).

4.  Then fold and iron again, bringing the outer edges to the middle "iron line" and iron along those edges. Repeat on other side.

5.  Re-iron the seam so that the Fabric is smooth and flat, it should now be 13 1/2" long x 7/8" wide.

6.  Open the top of the Fabric strip and trim the excess internal fabric at an angle so that there is less chance of the ends peeking out when sewn together.  Repeat on the other end.

7.  Pin the Fabric strip in a couple places to keep it in place.

8.   Sew a 1/8" seam all the way around the piece making sure to back stitch at the start and finish to set the seam.

9.  Now installed a Cap and Stud about 1/2" from the edge and the mating Cap and Socket about 1 1/2" later so that the center of the two KAM Snap parts are about 1 1/2" or more apart.  Any closer and I found I had trouble getting the MAM Ring or O-Ring Adapter to sit neatly inside.   I used Size 20 snaps for this tutorial but either Size 20 or Size 16 will work great.

10.  Repeat on the other side, that will hold the Pacifier Clip.  I, then, feed the Pacifier Clip and MAM Ring Adapter onto the ribbon and snapped it into place.  It may have been easier to thread on the pacifier clip before installing any Snap parts but I was able to feed it through without much trouble.

11.  Tada!  Now time to add the Pacifier.

12.  Simply stretch the MAM Ring or O-Ring around the Button Style Grip on the Pacifier and it will settle behind it and hold the Pacifier securely. Now snap the Pacifier in place, attach to your child's shirt and go.

13.  As pictured, the MAM Rings hold the same way as the O-Rings only with a less subtle profile.

14.  Tada!  Happy Snapping!!!

Water Bottle Marker/Charm Tutorial using MAM and O-Ring Pacifier Adapters August 24 2016

These adapter rings also can be used as water bottle markers or so you can easily attach your bottle to a clip.  Simply stretch the ring over the neck of a standard sized water bottle (~1”) to easily recognize your drink.  We carry 13 great ring colors to choose from.

*Take 10% our MAM and O-Ring Adapters with coupon code (thru Monday 8/29): RINGLOVE

Supplies:

• Standard Water Bottle (~1" mouth)
• MAM Ring Adapter or O-Ring Adapter

1.  Stretch Colored Ring Adapter of your choosing over the mouth of the bottle, just past the lip.

2.  So many uses.  Simply:

• Leave as a water bottle marker.
• Attach a carabiner clip and hang from your backpack, bag, belt loop or other.
• Hang from your lanyard for hands free carrying.

3.  Super easy and useful!  To see our Pacifier Clip Tutorials using MAM or O-Rings check them out here.

Happy Customers Make Our Day!!! June 30 2016

Today, I was reading through our feedback and just wanted to share what a few of our happy customers had to say:

♥ Color choices were fantastic and was able to get a mix of colors. My order arrived very quickly and was exactly what I had special ordered. Will definitely order from this site again!

♥ I continue to buy all my snaps from this seller. 5 Star Seller!

♥ These look great on my diapers! I love the color and they came quickly!

♥ I big BUTTons and I can not lie; Fast shipping of just what I asked for. Thank you!

♥ Exactly what I was looking for to make pacifier clips. Love the colors and the shipping was very fast! Thanks!!!

♥ I've ordered from this seller multiple times and have always been very happy with my purchases. Huge selection of items and fast, fast shipping!

♥ All snaps are packaged in small bags with info on it (color name and number), to make it easier to re-order... Love that!!! Great product! SUPER customer service! ... quick answering of messages... Super nice!!!

♥ Great items, great prices and will be back for more, thanks for fast shipping

♥ Love this shop! I needed to make 75 key fobs in a hurry and they shipped on Saturday of Memorial Day weekend so I could make my deadline. Great customer service. The hardware was just what I needed and arrived super fast.

♥ LOVE these snaps! So many colors & great prices too! A+++

♥ Sent everything just as ordered! Awesomeness!

Thank you to all of you who take the time to post your positive experience, it makes our day to see how all our hard work is appreciated!!!

Thank you, I Like Big Buttons! and all our Little Buttons!

An I Like Big Buttons Christmas! Idea #6: How to make a Sensory Ribbon Baby Tag Blanket with KAM Snaps & Pacifier Supplies December 16 2015

Gift Idea #6:  Fun and functional, Sensory Ribbon Tag Blanket with BONUS accessories make a great gift for any sweet little person in your life.  Use KAM Snaps or a KAM Pacifier Clip to make your blanket attachable or unthrowable :).  Add KAM Snaps, MAM Pacifier Rings or Pacifier O-Rings to add a Pacifier holder to your tag blanket.  I used them all :P to show you the different options.

Supplies:

• 2 12″x12″ Pieces of Fabric (1 Cotton and 1 Minky)
• 8x 5″ Piece of Ribbons (mix of Grosgrain and Satin)
• 7x 8" Piece of Ribbons (mix of Grosgrain and Satin)
• 1x 12" Piece of Ribbon
• 1 KAM Snap Set
• KAM Snap Pliers and Awl
• 1 KAM Pacifier Clip
• 1 MAM Pacifier Ring
• 1 Pacifier O-Ring
• Standard Sewing Machine

Instructions:

1.  Cut the Fabric and Minky material to 12"x12" squares and cut your mix of ribbon 8 in 5" lengths, 7 in 8" lengths, and 1 in 12" length.  See More

#ilikebigbuttons #kamsnaps #plasticsnaps #sootherblanket #christmasideas

30 Days of KAM Snaps and Beyond!!! How to make Cover Button Metal Pacifier Clips with Cover Buttons, Round Faced Metal Suspender Clips and KAM Snaps September 24 2014

Day #35

How to make a Cover Button Metal Pacifier Clips with Cover Buttons, Round Faced Metal Suspender Clips and KAM Snaps

Today I am making Cover Button Pacifier Clips using Round Faced Metal Pacifier Clips (Metal Suspender Clips), Size 36 Cover Buttons, and KAM Snaps, of course ;).  I have had a lot of questions in the last year about how to make these clips so I decided to take it on.  Keep in mind that although I have rough tested these I in no way recommend you leave your baby alone with these as there are small pieces and if not done properly they may come apart and become a choking hazard.  I would recommend these clips under adult supervision only.  The maker and/or parent assumes full responsibility when using these pacifier clips.

That being said I did rough test these and was unable to break them apart after they had proper time to dry and cure.  I didn't take a hammer to them :) but I did my best to undo my hard work and was not able to.

Supplies:

• 2 KAM Snap Sets
• KAM Snap Pliers and Awl
• Round Faced Metal Clips or Enamel Pacifier Clips
• 1 Size 36 Flat Back Cover Button
• Size 36 Assembly Tool
• Size 36 Template
• Fabric Scraps
• E6000 Adhesive
• Pre-made Pacifier Clips (see Pacifier Clip and Supply Tutorials)

Instructions:

1.  Using our Pacifier Clip and Supply Tutorials make either Ribbon or Fabric Pacifier Clips.

2.  Cut your fabric scrap. You will want a circle that is about twice the diameter of your button blank.  I cut out a Piece of Fabric using my Size 36 Template.

3.  Put your fabric piece in the larger assembly tool piece (RIGHT SIDE DOWN). When you look into the tool you want to see the back of the fabric.

4.  Place the button front (the domed piece) on top of the fabric. Leave the fabric edges hanging out.  Double check the transparent underside to see if your print is how you would like it.   Then press the cover button fabric edges down into the tool.

5.  Add a dab of E6000 Adhesive to the middle of the cover button cap before installing the Flat Back.

6.  Place the back cover button piece on top of your fabric and button front.

7.  Take the smaller piece of the assembly tool and with the open side down place it on the button back.

8.  Press down. You may hear a pop when the last bit of the button back slips into place. If you take the tool out and the button is not completely secured, just put it back in and press down again.

9.  When you take the small assembly tool piece off, the fabric edges will be secured underneath the button back.

10.  Remove the button from the larger assembly tool piece.  Tada!  My Cover Button is ready to be adhered to a Round Faced Metal Clip.

11.  Here a the Cover Buttons I made in just a few minutes.  Seriously easy, fun and so cute!

12.  Now take the E6000 Adhesive and put a medium size dab of glue on the back of the cover button about 1/2 of what would fill the back area of the back.  This glue is great to work with so don't overly worry about getting the amount right.  I was able to cleanly wipe of any excess off when I put on too much and I was also able to remove the button and add a little more when I under did it.  This glue is very forgiving.

13.  Now place the Cover Button over the Round Faced Metal Pacifier Clips and straighten and center your button.

14.  Press firmly and let set to dry and cure 24-72 hours as recommended by the manufacturer (E6000).

15.  These are my finished products.  I love them and think they turned out beautifully.  Below are my examples, completed and installed on Pacifier Clips.

16.  Tada!!!

Disclaimer:  Keep in mind that although I have rough tested these I in no way recommend you leave your baby alone with these as there are small pieces and if not done properly they may come apart and become a choking hazard.  I would recommend these clips under adult supervision only.  The maker and/or parent assumes full responsibility when using these pacifier clips.

30 Days of KAM Snaps and Beyond!!! How to make a "No Sew" Pacifier Clip with KAM Snaps, MAM Ring or O-Ring and an KAM Plastic Pacifier Clip for Button Style Pacifiers September 05 2014

Day #33

How to make a "No Sew" Pacifier Clip with KAM Snaps, MAM Ring or O-Ring and an KAM Plastic Pacifier Clip for Button Style Pacifiers

Today, I am making a "No Sew" Pacifier Clip for Button Style Pacifiers using our silicone MAM rings and O-Rings.  No sewing necessary!

Supplies for a "No Sew" Pacifier Clip with Button Style Pacifier Adapters:

• Pacifier with Button Style Grip
• 16-18" of 1/2", 3/4" or 7/8" Grosgrain Ribbon
• 1 Enamel Clip or Plastic Clip per Clip
• 2 KAM Snap Sets per Clip
• KAM Snap Pliers and Awl
• MAM Ring and O-Ring Button Style Adapters
• Fabric Tac
• Lighter or Chef's Torch

Instructions:

1.  Choose a 7/8" or 3/4" or 1/2" Grosgrain Ribbon, cut a 16" to 18" length of ribbon.  I did some of each size of Grosgrain Ribbon and I cut them 16" long so when they were completed they was approximately 12" long.

2.  The ribbon I was using was made of polyester so I used a lighter to seal the ends of the ribbon so it doesn't fray.  (If you are unsure, you may want to practice on a scrap piece if this is your first time or you are unsure of the what the material is made of.)

3.  Then I used a bit of Fabric Tac and folded over an 2" to 1 1/2" of the ribbon back on itself to reinforce the ribbon and pressed it firmly and let it dry.  Repeat on the opposite end.

4.  Once dry, I installed a Cap and Stud in each end of the ribbon about 1/2" from the edge.  Then I installed the Cap and Socket about 1 1/2" apart so that the center of each KAM Snap is about 1 1/2" or more apart.  Any closer and I found I had trouble getting the MAM Ring or O-Ring Adapter to sit neatly inside.  I used Size 20 snaps for this tutorial but either Size 20 or Size 16 will work great.

5.  Repeat on the other side, that will hold the Pacifier Clip.  I, then, feed the Pacifier Clip and MAM Ring Adapter onto the ribbon and snapped it into place.  It may have been easier to thread on the pacifier clip before installing any Snap parts but I was able to feed it through without much trouble.

6.  Tada!  Now time to add the Pacifier.

7.  Simply stretch the MAM Ring or O-Ring around the Button Style Grip on the Pacifier and it will settle behind it and hold the Pacifier securely. Now snap the Pacifier in place, attach to your child's shirt and go.

8.  As pictured, the O-Rings hold the same way as the MAM Rings only with a more subtle profile.

9.  Tada!  Happy Snapping!!!

30 Days of KAM Snaps and Beyond!!! How to make a Fabric Pacifier Clip with KAM Snaps, MAM Ring or O-Ring and an KAM Plastic Pacifier Clip for Button Style Pacifiers August 27 2014

Day #32

Making a Fabric Pacifier Clip with KAM Snaps, MAM Ring or O-Ring and an KAM Plastic Pacifier Clip for Button Style Pacifiers

Today, I am making a pretty Fabric Pacifier Clip for Button Style Pacifiers using our silicone MAM rings and O-Rings. Pretty functional :)!!!

Supplies for a Fabric Pacifier Clip with Button Style Pacifier Adapters:

• Pacifier with Button Style Grip
• 14" x 3 1/2" Piece of Fabric
• 1 Pacifier Clip per Clip
• 2 KAM Snap Sets per Clip
• KAM Snap Pliers and Awl
• MAM Ring and O-Ring Button Style Adapters
• Standard Sewing Machine and Iron

Instructions:

1.  Choose a piece of Fabric, cut it to the dimensions: 14" x 3 1/2", the finished product once ironed, folded and sewn will be approximately 7/8" wide x 12" long.

2.  Fold both 3 1/2" wide ends in 1/4" and iron flat.

3.  Now fold and iron the fabric in half the long way (14" length).

4.  Then fold and iron again, bringing the outer edges to the middle "iron line" and iron along those edges. Repeat on other side.

5.  Re-iron the seam so that the Fabric is smooth and flat, it should now be 13 1/2" long x 7/8" wide.

6.  Open the top of the Fabric strip and trim the excess internal fabric at an angle so that there is less chance of the ends peeking out when sewn together.  Repeat on the other end.

7.  Pin the Fabric strip in a couple places to keep it in place.

8.   Sew a 1/8" seam all the way around the piece making sure to back stitch at the start and finish to set the seam.

9.  Now installed a Cap and Stud about 1/2" from the edge and the mating Cap and Socket about 1 1/2" later so that the center of the two KAM Snap parts are about 1 1/2" or more apart.  Any closer and I found I had trouble getting the MAM Ring or O-Ring Adapter to sit neatly inside.   I used Size 20 snaps for this tutorial but either Size 20 or Size 16 will work great.

10.  Repeat on the other side, that will hold the Pacifier Clip.  I, then, feed the Pacifier Clip and MAM Ring Adapter onto the ribbon and snapped it into place.  It may have been easier to thread on the pacifier clip before installing any Snap parts but I was able to feed it through without much trouble.

11.  Tada!  Now time to add the Pacifier.

12.  Simply stretch the MAM Ring or O-Ring around the Button Style Grip on the Pacifier and it will settle behind it and hold the Pacifier securely. Now snap the Pacifier in place, attach to your child's shirt and go.

13.  As pictured, the MAM Rings hold the same way as the O-Rings only with a less subtle profile.

14.  Tada!  Happy Snapping!!!