Fabric Pacifier Clip with KAM Snaps, MAM Ring or O-Ring and an KAM Plastic Pacifier Clip for Button Style Pacifiers September 21 2016

Today, I am making a pretty Fabric Pacifier Clip for Button Style Pacifiers using our silicone MAM rings and O-Rings. Pretty functional :)!!!

******************************************************************

Don’t forget to enter our Super-Sized KAM Plastic Pacifier Clips and Snap Giveaway!!!  Only 5 days left:

a Rafflecopter giveaway

Also, if you don’t want to wait, you can get 10% off our Pacifier Supplies on our website with Coupon Code: PACI2016

******************************************************************

Supplies for a Fabric Pacifier Clip with Button Style Pacifier Adapters:

Fabric Pacifier Clip with MAM O Ring pic 18

Fabric Pacifier Clip with MAM O Ring pic 1

Instructions:

1.  Choose a piece of Fabric, cut it to the dimensions: 14" x 3 1/2", the finished product once ironed, folded and sewn will be approximately 7/8" wide x 12" long.

Fabric Pacifier Clip with MAM O Ring pic 2

Fabric Pacifier Clip with MAM O Ring pic 3

2.  Fold both 3 1/2" wide ends in 1/4" and iron flat.

Fabric Pacifier Clip with MAM O Ring pic 4

3.  Now fold and iron the fabric in half the long way (14" length).

Fabric Pacifier Clip with MAM O Ring pic 5

4.  Then fold and iron again, bringing the outer edges to the middle "iron line" and iron along those edges. Repeat on other side.

5.  Re-iron the seam so that the Fabric is smooth and flat, it should now be 13 1/2" long x 7/8" wide.

Fabric Pacifier Clip with MAM O Ring pic 6

6.  Open the top of the Fabric strip and trim the excess internal fabric at an angle so that there is less chance of the ends peeking out when sewn together.  Repeat on the other end.

Fabric Pacifier Clip with MAM O Ring pic 7

7.  Pin the Fabric strip in a couple places to keep it in place.

Fabric Pacifier Clip with MAM O Ring pic 8

8.   Sew a 1/8" seam all the way around the piece making sure to back stitch at the start and finish to set the seam.

Fabric Pacifier Clip with MAM O Ring pic 9

9.  Now installed a Cap and Stud about 1/2" from the edge and the mating Cap and Socket about 1 1/2" later so that the center of the two KAM Snap parts are about 1 1/2" or more apart.  Any closer and I found I had trouble getting the MAM Ring or O-Ring Adapter to sit neatly inside.   I used Size 20 snaps for this tutorial but either Size 20 or Size 16 will work great.

Fabric Pacifier Clip with MAM O Ring pic 10

10.  Repeat on the other side, that will hold the Pacifier Clip.  I, then, feed the Pacifier Clip and MAM Ring Adapter onto the ribbon and snapped it into place.  It may have been easier to thread on the pacifier clip before installing any Snap parts but I was able to feed it through without much trouble.

Fabric Pacifier Clip with MAM O Ring pic 11

Fabric Pacifier Clip with MAM O Ring pic 12

11.  Tada!  Now time to add the Pacifier.

Fabric Pacifier Clip with MAM O Ring pic 13

Fabric Pacifier Clip with MAM O Ring pic 14

Fabric Pacifier Clip with MAM O Ring pic 15

Fabric Pacifier Clip with MAM O Ring pic 16

12.  Simply stretch the MAM Ring or O-Ring around the Button Style Grip on the Pacifier and it will settle behind it and hold the Pacifier securely. Now snap the Pacifier in place, attach to your child's shirt and go.

Fabric Pacifier Clip with MAM O Ring pic 19

Fabric Pacifier Clip with MAM O Ring pic 20

Fabric Pacifier Clip with MAM O Ring pic 22

13.  As pictured, the MAM Rings hold the same way as the O-Rings only with a less subtle profile.

Fabric Pacifier Clip with MAM O Ring pic 17

Fabric Pacifier Clip with MAM O Ring pic 18

14.  Tada!  Happy Snapping!!!