News
I Like Big Buttons! LEGO Earrings and Cover Button Bracelet September 24 2018
Today I worked alongside my daughter to make her dear friend a special and one of a kind birthday gift. I think they turned out great and it was wonderful to get to work with one of my kiddos. :)
LEGO Earring Supplies:
- 2x LEGO Bricks of your choosing (We used 2x2's)
- E6000 Adhesive or Hot Glue
- Clip On Earring Backs or Surgical Stainless Steel Earring Posts and Backs
LEGO Bracelet Supplies:
- 11-13 x LEGO Bricks of your choosing (We used 2x2's and LEGO Dots)
- 1 Disk and Loop Bracelet (We have two sizes available 7.2" or 8.25")
- E6000 or comparable adhesive
This project would also work great with our Barrettes, Bobby Pins, Badge Reels, or Cufflinks.
Check out our other great jewelry Tutorials, by visiting our DIY Project section here.
I Like Big Buttons! Lacy Fabric Cover Button Earrings and Cover Button Bracelet November 12 2016
Today I worked alongside my daughter to make her dear friend a special and one of a kind birthday gift. I think they turned out great and it was wonderful to get to work with one of my kiddos. :)
Take 10% off our Cover Buttons on our website (Good through 11/14): BUTTONLOVE
Lacy Fabric Cover Button Earring Supplies:
- Flat Back Cover Buttons (I used Size 30, but you can also use Size 24 and Size 36 Cover Buttons)
- Cover Button Assembly Tools
- Cover Button Templates
- Fabric Scraps
- Lace Scraps
- E6000 Adhesive or Hot Glue
- Sharpie Permanent Marker
- Clip On Earring Backs or Surgical Stainless Steel Earring Posts and Backs
Lacy Fabric Cover Button Bracelet Supplies:
- Size 20 Flat Back Cover Buttons
- Cover Button Assembly Tools
- Cover Button Templates
- Fabric Scraps
- Lace Scraps
- 11 to 13 - Completed Size 20 Flat Back Fabric Cover Buttons
- 1 Disk and Loop Bracelet (We have two sizes available 7.2" or 8.25")
- 11 to 13 - 1/2" x 1/2" Felt squares
- E6000 or comparable adhesive
Check out our Tutorials below.
Lacy Fabric Cover Button Earring Tutorial here.
Fabric Cover Button Bracelet Tutorial here.
To see our other great Fabric Cover button ideas, visit our DIY Project section here.
I Like Big Buttons! Fabric Cover Button Bracelet Tutorial October 06 2016
Today I am making a Fabric Cover Button Bracelet. I have been eyeing these for a while. I love the mix of metal and fabric. Mix and match fabrics or go for a solid theme. There are so many possibilities. Layer more than one bracelet to make a statement.
Supplies:
- 11 to 13 - Completed Size 20 Flat Back Fabric Cover Buttons
- 1 Disk and Loop Bracelet
- 11 to 13 - 1/2" x 1/2" Felt squares
- E6000 or comparable adhesive
Steps:
1. Follow these instructions to make Flat Back Fabric Covered Buttons.
2. Lightly scuff the tops of the gluepads so the glue will adhere better (not essential but recommended).
3. Lightly scuff the back of the Cover Button so the glue will adhere better (not essential but recommended).
4. Clean both surfaces of dust.
5. Apply E6000 to back of Cover Button.
6. Press Felt square into E6000 firmly. This is to fill the gap between the back and the surface of the disk (gluepad).
7. Apply another dab of E6000 to the Felt square.
8. Press the Size 20 Cover Button firmly onto the disk (gluepad) and center it.
9. Repeat 10 more times.
10. Let dry and enjoy!
11. Tada!
You are done! Make this bracelet to accent your favorite outfit or to make a statement. Enjoy!
To see our other great Cover Button Tutorials here.